Netgear Nighthawk X4 R7500 router steps to change the IP Address

Login To The Netgear Nighthawk X4 R7500

To get started configuring the Netgear Nighthawk X4 R7500 LAN page you need to login to your router. If you are already logged in you can skip this step.

To login to the Netgear Nighthawk X4 R7500, follow Netgear Nighthawk X4 R7500 Login Guide.

our call at toll free number 1888 479 2017 for USA/ 1800 987 893 for Australia

Change the LAN IP Address on a Netgear Nighthawk X4 R7500

 On the Home page of the Netgear Nighthawk X4 R7500 router. To change your IP address go to the ADVANCED tab near the top of the page. From there click Setup and then LAN Setup below that.

Configure the LAN section of your Netgear Nighthawk X4 R7500

On this page you have the option to change your router's IP Address. 10.0.0.1

Below that is the option to change your IP Subnet Mask. Leave this alone. It needs to stay at 255.255.255.0

That's all there is to it. Just be sure to click Apply before closing the page.

Possible Problems when Changing your LAN IP Address

 You will lose your Internet connection when you apply these changes. Your router may reboot and require a couple of minutes to start responding again.

some computers might need to reboot.

If face issues to change IP address than easily you can call our tech support team to take care of that issue, 

Our certified experts can solve all types of Netgear Router related problems including installation, upgrade, uninstallation, configuration, settings or customization.

Call us at our toll free numbers:

USA : 1888 479 2017

Australia: 1800 987 893

or else you can log on to our website :

https://www.icognix.net/support-for-netgear-routers/

SET UP WIRELESS SECURITY FOR NETGEAR ROUTERS

WANT TO CHANGE YOUR NETGEAR ROUTER SETTING LET THIS STEP HELP YOU OUT.

1. From a computer connected to your router, go to 192.168.0.1
   
   
2. Enter the details below when asked to log in
   
   - User name: admin
   - Password: password
   
   
3. The Netgear's admin pages will open
   
   
4. If the router starts checking for new firmware, click Cancel
5. Select Wireless Settings from the Setup menu
   
   
   
6. The Wireless Network field is where you'll find your wireless network name
   
   - Name (SSID): You can change this to something new and personal to you
   - Region: select Europe
   - Channel: select Auto
   - Mode: select Up to 150Mbps
   
   
7. In the Wireless Access Point field
   
   - Check Enable Wireless Access Point
   - Check Allow Broadcast of Name (SSID)
   - Don't check Wireless Isolation
   
   
   
8. In the Security Options field, select Mixed WPA-PSK+WPA2-PSK
   
   
   
9. In the Network Key field you'll find your security key or password
10. If you'd like, you can enter a new security key for your connection
    
    This should be over eight characters and can be made up of upper and lower case letters from a-z and numbers 0-9.
    
    
    
11. Click Apply - any changes you've made will be updated
12.  If you face any issue at above steps than please let us know. You can fix your technical issue for your netgear router through our technicians who are professional and Microsoft certificated . At netgear tech support we provide All router issues instantly. Let us help you out call us at our toll free numbers 
13. USA : 1888 479 2017
14. UK: 0800 368 9229
15. you log on to our web site at:  https://www.icognix.net/netgear-router-support/
16.   Were these steps usefull to you let us know please leave comments.

Wireless Extender (Netgear WiFi Range Extender – WN2000RPT) AT&T U-verse Router (Windows and Macintosh)

Using Wireless Extender (Netgear WiFi Range Extender – WN2000RPT) on AT&T U-verse Router (Windows and Macintosh)

12APR

There are tricks in order to use wireless extender on AT&T U-verse router.

Just connecting the extender and complete the extender’s configuration will only give you access to the network, but not the Internet access. This means, you can access the computer within the network, but you can’t access the Internet. 

1. Go to Netgear configuration manager.
2. 
3. 
   
4. Turn off DHCP feature on the extender by going to “IP Address Setup” and use static ip address.
   On “IP Address” field, specify the ip address you want for the extender. Remember this ip address.
   Do note that the “Gateway IP Address” and “Primary DNS” are the ip of your AT&T U-verse router. By default, the AT&T U-verse router’s ip is 192.168.1.254.
   
5. Click Apply button to save the setting.
6. Now, configure your computer’s network setting to point its default gateway and primary dns to the extender’s ip address.
7. On Windows, open up the network adapter setting.
   
8. Display the properties.
   
9. Properties on “Internet Protocol Version 4 (TCP/IPv4)” or something similar to that.
   
10. Define ip address and dns server address.
    On “IP address”, specify ip address you want for this computer.
    On “Default Gateway” and “Preferred DNS server”, type in the AT&T U-verse router’s ip address. By default, the AT&T U-verse router’s ip is 192.168.1.254.
11. Go back to network adapter setting to restart the connection (disable and then enable again).

Mac users: you can do the same thing: point your Mac’s network default gateway and dns server address (router) to AT&T U-verse router’s ip address.

To access your network setting, go to System Preferences > Internet & Wireless > Network > Advanced > TCP/IP.

The side effect (not sure if it’s good / bad…) of using this technique is your AT&T U-verse router will assign a ‘dynamic’ ip address for the extender. What I meant by ‘dynamic’ here is, the ip address will constantly change depend on what device is making connection to AT&T U-verse router. So for example, you have specify the extender ip address as 192.168.1.1 in the extender’s configuration manager and you have 2 devices connecting to the extender with ip addresses as 192.168.1.5 and 192.168.1.6 respectively, the extender ip address in AT&T U-verse router will change from 192.168.1.1, 192.168.1.5 or 192.168.1.6.

IF STILL THERE IS A ISSUE THAN PLEASE CALL US AT 1888 479 2017.

we have the most experienced and certified Netgear tech support professionals onboard. Our experts offer customized solution to help you overcome the router issues. They are available round the clock over phone, email and web chat for all types of Netgear technical support.

OR LOG ON TO OUR WEBSITE:  

https://www.icognix.net/netgear-router-support/

THANK YOU.

Netgear router Wireless Router Keep Disconnecting or Dropping the Connection

The issue is usually caused by one of three things: the driver for your wireless card, the firmware version on your netgear router (basically the driver for the router) or settings on your router

In this post there are 3 methods which can fix this issue.

Update PC Driver

First, you’ll need to go to the web site for the manufacturer of your computer: Dell, HP, Toshiba, etc and go to their support or driver downloads page. 

Select your system or type it in and find the latest driver for you wirless card. There is usually a section called Networking and underneath you should see a list of drivers. One of them should have the word “Wireless” in it. If you have more than one wireless driver, then you need to figure out which one you have installed on your computer.

 determine the model number for your wireless card by pressing the Windows key + the Pause button at the same time. This brings up the System Properties dialog. Another way to get to it is to right click on My Computer and select Properties. Once there, click on Advanced system settings.

Click on the Hardware tab and then click on Device Manager.

You’ll see a list of devices with plus signs to the left of them. Click on the one called “Network Adapters” and there will be an entry for your wireless card as shown below:

Now download that driver from the list off the manufacturers web site. Usually the wireless card is called something “Intel Pro Wirelss” or “Dell Wireless”, etc. Once you download the file to your desktop, double click on it and follow the steps to install. You might have to restart your computer.

If the driver on the computer was the problem, the dropped connections should go away completely. If not, then you might have to try updating the router firmware.

Update Netgear Router Firmware

Updating router firmware is a not so trivial task that varies depending on the router brand you happen to have. Almost none of them have an automatic update feature. Instead you have to download the latest firmware from their website, log into your router and then upload it up perform the update. If your having issue to find call us we would help you out 1888 479 2017

To get started, you need to figure out the IP address of your router and use that to log in via a browser. Read my post on finding the IP address for a wireless access point. Since the method to update the router firmware varies so much by brand, it’s best to search your router model number + “firmware update” to find specific instructions.

Router Settings

The last issue that can be causing dropped connections is various settings on your router. In recent times, you have dual-band routers which let you broadcast on both 2.4 and 5 GHz networks. These advanced routers normally work really well with the latest gadgets and computers, but on older machines, you can sometimes run into issues. Here’s a couple of things I would try:

1. Connect to the 2.4 GHz network if you’re currently connected to the 5 GHz one.

2. On the router, make sure the channel settings for the networks is set to Auto. If you have picked a particular channel for some reason, try a different channel.

3. Turn off extra security features like MAC address filtering, network isolation and Wi-Fi Protected Setup. None of these really increase security all that much and end up causing more trouble.

4. Make sure your wireless network mode is set to Mixed. Sometimes picking a higher mode can cause problems with older devices.

5. If you don’t know anything about your router settings, try resetting your router completely by pressing the reset button. Configure wireless security and leave it at that.

Hopefully one of these solutions will fix  wireless connection problem. 

or

You can take help of professional technicians to fix it.  We have a team of Netgear router support professionals, who are well-versed in handling all types of router related issues.

The most experienced and certified Netgear tech support professionals on board. Our experts offer customized solution to help you overcome the router issues. They are available round the clock over phone, email and web chat for all types of Netgear technical support.

 USA :1-888-479-2017 | Toll-free CAN :1-888-536-4211 |  Email: support@icognix.com

website: https://www.icognix.net/netgear-router-support/

Netgear router technical support number USA 1888 479 2017: Configure your router for cable internet connectio...

Netgear router technical support number USA 1888 479 2017: Configure your router for cable internet connectio...:      NETGEAR 1. Unplug the modem and router power cords. Note : If you have a back-up battery on your modem, remove it tempora...

Configure your router for cable internet connection with NETGEAR genie

     NETGEAR

1. Unplug the modem and router power cords.
Note: If you have a back-up battery on your modem, remove it temporarily.

2.    Connect an Ethernet cable from the modem to the Internet port of the router

3.    Connect an Ethernet cable from the computer to any one of the LAN ports of the router.

4.    Re-insert the back-up battery (if any) and reconnect the modem power. Wait for all lights to become stable.

5.    Reconnect the power of the router and wait for the power light to become green.

6.    Open a web browser and type the router's IP address which would be either http://192.168.0.1 or http://192.168.1.1 in the address bar and press Enter.

o    You are prompted to log into the router.

o    The default username is admin and the default password is password. 

o    If you need additional assistance with router you can call us at 1888 479 2017

7.    You are prompted to enter a username and password. Enter the following default login credentials:

o    Username: admin

o    Password: password

8.    Click ADVANCED > Setup Wizard.

9.    Select Yes and click Next.



Note: The Setup Wizard will now detect the internet connection type.

10.  Once the setup has finished configuring the internet connection, the Congratulations page displays.
Click Take me to the Internet to test the connection.

  If you need more assistance than you just call our toll free number to get technical support instantly. we provide solutions for routers  instantly. you just call at our toll free number that is 1888 479 2017

   your you can log to our web site :

   https://www.icognix.net/netgear-router-setup/

netgear router support

NETGEAR ROUTER CONNECTION ISSUE RESOLVING STEPS

 Options to try in resolving your connection issues:

Changing to a different wireless channel:

1. Click on Wireless Settings below the setup menu.
2. Change the Channel (any channel can be used).
3. Click Apply and test for improvement in performance.

Note: The Wireless Settings option is available under Advanced Setup in routers with the newer genie interface.

Try reducing the connection speed:

1. Click  Wireless Settings below the setup menu.
2. Change the Mode to a lower speed.
3. Click Apply and test for improvement in performance.

Adjust advanced wireless settings:

1. Click Wireless Settings under Advanced.
2. Change the Fragmentation Length and CTS/RTS Threshold values to 2304.
3. Click Apply and test for improvement in performance.
   
   
   
4. IF NOT RESOLVED THAN PLEASE CONTACT OUR TECH SUPPORT TEAM FOR TECHNICAL HELP, 
5. APART FROM CONNECTION ISSUE YOU CAN RESOLVE ALL  ISSUE RELATED TO YOUR NETGEAR ROUTERS.
6. OUR PROFESSIONAL TEAM IS AVAILABLE 24\7 TO SERVE YOU.
7. JUST CALL US AT OUR TOLL FREE NUMBER THAT IS 1888 479 2017 FOR USA CUSTOMERS
8. OR BY LOGGING ON TO OUR WEBSITE AT: https://www.icognix.net/netgear-router-support/
9. HOPE THE ABOVE STEPS WOULD HELP.